Performance Products

3.3 Light Weight Flywheel 3-Shoe Clutch Kit

This is the Hot Racing 3 Piece Clutch with Flywheel for the Traxxas Revo, T-Maxx, Nitro Rustler, Nitro Stampede, or Jato (works with 2.5, 2.5R or 3.3 engines) FEATURES: Light Weight Flywheel CNC 6061-T6 aluminum construction (Blue in color) 7075 T6...

Black Aluminum Secure Lock Rear Bulkheads

Features:CNC Constructed of billet machined 6061 aluminum with added two fastener point to secure lock and hold the gear mesh in placeReplaces stock plastic bulkheadCNC Constructed of billet machined 6061 aluminum with added two fastener point to secure...

Steel Pinion and Spur Gear Set 18 Tooth, 60 Tooth, 32 Pitch

Hot Racing's light weight hardened steel 18T/60T 32 pitch pinion and spur gear set for the Traxxas Bandit, Rustler, 2WD Slash, and 2WD Stampede.Features:CNC machined and lightened hardened steel constructionReplaces stock nylon spur gearRugged 0.8...

Aluminum Front Bumper Winch Mount & Light Buckets, for Tra

Hot Racing aluminum front bumper with LED light buckets, winch mounting pattern, and tow shackles for the Traxxas TRX-4 or Axial SCX10 II.Features:CNC machined billet aluminum bumper, anodized semi-flat blackSolid aluminum stingerPre-drilled mm mounting...

Ultra Low Range Crawl Transmission, for TRX4-M

Hot Racing aluminum Ultra low range crawl Transmission for the TRA TRX-4 Mini vehicle model.COMMENTS: Replaces part of TRA9747, 9791, 9791X, 9791RIncludes:One (1) aluminum Sliding fine tune gear mesh motor mount Transmission with Ultra low range hardened...

Brass Wheel, for Axial SCX 24 (2pcs)

Hot Racing machined billet Brass wheels (rims only) for the 1/24 Axial SCX 24.Features:Fits Axial SCX 24 tires only (AXI31567)CNC machined billet Solid BrassNo Hex Drive design to maximize wheel weight.Specifications:Wheel diameter: 26.5mmWeight:...

Aluminum Battery Hold-Down W/ Heat Sink Traxxas X-Maxx

Hot Racing aluminum battery hold-down with integrated heatsink for the Traxxas X-Maxx 6S and 8SYOU WILL RECEIVE: One (1) left battery hold-down One (1) right battery hold-downREQUIREMENTS: InstallationCOMMENTS: Replaces Traxxas plastic 7719 battery...

Aluminum Transmission Case for Slash, Rustler & Stampede

Aluminum transmission gearbox case with aluminum motor plate and arm mounts for use in the Traxxas Bandit, Rustler, 2WD Stampede, and 2WD Slash.YOU WILL RECEIVE:- One (1) aluminum transmission case with aluminum heat sink motor plate- Left and right...

Alum Bearing Saver Steering Kit - T-Maxx E-Maxx

Hot Racing aluminum steering bellcrank with built-in servo saver for the Traxxas T-Maxx or E-Maxx. Requirements: E-Maxx or T-Maxx that uses the Traxxas 4945 steering rack (refer to your vehicle's manual)Features:Super-tough, fully adjustable servo...

Aluminum Front Bumper Mount, for Axial SCX24

Hot Racing aluminum front bumper mount frame crossmember for the Axial SCX24 vehicles.Features:Stronger and more rigid than factory plastic cross-member for a more rigid frame and more predictable and consistent chassis performanceOne-piece CNC machined...

Knuckle Portal Cover, Brass,

Features:CNC machined solid brassHeavy to add weight to vehicle for greater stability.Improve weight distribution for better performanceDirect replacement for factory plastic steering knuckles Portal Gear CoverSpecifications:Weight 41g (1.4oz) eachCNC...

Steel Pinion & Spur Gear Kit, 18/58T 32P (0.8Mod)

Hot Racing Blue Power Up HD 58T 32pitch Spur Gear for the Traxxas Rustler, Stampede and Slash. FEATURES: Rugged 0.8 Module/32pitch teeth for total reliability on brushless power. CNC Machined Harden Black steel teeth attached to hub with three screws One...

Alum +6mm 17mm Hubs, Hex Serrated Nuts, for Traxxas MT

Hot Racing's +6mm/side extended 17mm hex hub wheel adapters for the Traxxas E-Maxx, E-Revo, Revo, Summit, and T-Maxx. These increase the track width of the vehicle to increase stability and replace the existing hexes so the vehicle can accept wheels with...

Composite Gear Case with Aluminum Motor Plate

Composite transmission gearbox case with aluminum motor plate and arm mounts for use in the Traxxas Bandit, Rustler, 2WD Stampede, and 2WD Slash.YOU WILL RECEIVE:- One (1) composite transmission case with aluminum heat sink motor plate- Left and right...

Wheel Hub Adapters, Aluminum,

Hot Racing's aluminum 12mm to 17mm hex wheel hub adapters. These adapters are compatible with many 1/10th scale vehicles with factory 12mm hex hubs and allow the use of 17mm hex wheels, all while adding a 10mm width extension per side of the vehicle for...